[inder]

Trying to talk to the Central Convenience Module in my Polo 1.4 Year 2000, but Vag-Com keeps giving the module does not respond error

I've tried removing the battery to 'reboot' it, but it has not done the trick - just meant i have to put the radio code and clock back in :roll:

also saw removing fuses may do the trick - which ones? #s?

please help! i need access to it to setup anti hijack at least

can talk to other modules (well Instruments) so cable and connection is fine

:?: :?

 

[EddyH]

Does with 1.4 Polo have a central convenience system? Some lower spec models only have central locking and some don't even have that.

 

[Foxy]

Why not try dissing the battery ("you're a fat ugly mother battery") - and rebooting it all ........it worked for me!

 

[inder]

Ahh crap, you may be correct []

Mine is a 1.4 SE model, has central locking (not remote, but have DIY upgraded it to remote)

Can anyone confirm

Guess this means no anti-hijack can be activated?

Anyone with the same/similar model can advise which modules i have/can play with

thanks for the help and time

[|)]

 

[inder]

I will try abusing the battery with 'words' Foxy to see if that helps []

 

[Rally_Chris]

The central locking may have its own module rather than one called 'central convenience' - take a look at what modules are listed in VAG-COM.

Chris

 

[EddyH]

Quote: posted by inder on 30/03/2005 21:49:26

Ahh crap, you may be correct []

Mine is a 1.4 SE model, has central locking (not remote, but have DIY upgraded it to remote)

Can anyone confirm

Guess this means no anti-hijack can be activated?

Anyone with the same/similar model can advise which modules i have/can play with

thanks for the help and time

[|)]

Can you connect to the central locking module? You normally have one or the other not both.

 

[inder]

thanks for the advice, I will let vag-com do it's little scan thing and see what it lists as available and post back, tomorrow

[]

 

[inder]

done the 'everything' scan and it could only talk to a few things []

Address 01: Engine

Protocol: ????

Controller:

Note: Can't Synch Baud Rate

Address 03: ABS Brakes

Protocol: KW1281

Controller: 6X0 907 379 B

Component: ABS 30 IE CAN V004

Coding: 05603

Shop #: WSC 00788

Skipping Address 15-Airbags

Address 17: Instruments

Protocol: KW1281

Controller: 6N0 920 904 D

Component: KOMBIINSTRUMENT BOO V09

Coding: 00441

Shop #: WSC 00679

Address 19: CAN Gateway

Protocol: KW1281

Controller: 6N0 909 901

Component: Gateway K<->CAN

Coding: 00022

Shop #: WSC 00788

Address 33: OBD-II

Protocol: ????

Controller: OBD-II/EOBD, Protocol Keyword: $0808

Address 3F: Unknown Address: 3F

Protocol: KW1281

Controller:

Address 7C: Unknown Address: 7C

Protocol: ????

Controller: OBD-II/EOBD, Protocol Keyword: $7C86

What are the 'unknown' ones? [?]

Checked them for faults, none except on Instruments:

1 Fault Found:

01314 - Engine Control Module

49-10 - No Communications - Intermittent

What does this mean? [B)][]

Thanks in advance

 

[Uwe]

What version of VAG-COM?

What kind of interface?

What kind of PC?

-Uwe-

 

[inder]

Quote: posted by Uwe on 02/04/2005 03:15:30

What version of VAG-COM?

What kind of interface?

What kind of PC?

-Uwe-

hi

latest version from the site (demo), using a serial cable. just a p4 windows laptop

thanks

 

[Uwe]

"A Serial Cable" is not a type of interface.

I'm guessing what your response really means is that you bought some third party interface, perhaps off eBay? If so, have you considered asking the vendor or manufacturer of this interface for assistance?

-Uwe-

 

[inder]

Quote: posted by Uwe on 02/04/2005 16:49:37

"A Serial Cable" is not a type of interface.

I'm guessing what your response really means is that you bought some third party interface, perhaps off eBay? If so, have you considered asking the vendor or manufacturer of this interface for assistance?

-Uwe-

 

[inder]

Quote: posted by Uwe on 02/04/2005 16:49:37

"A Serial Cable" is not a type of interface.

I'm guessing what your response really means is that you bought some third party interface, perhaps off eBay? If so, have you considered asking the vendor or manufacturer of this interface for assistance?

-Uwe-

Hi Uwe, thanks for the reply. I am not looking for cable assitance, I am looking for info about this error code Vag-Com has found for me:

1 Fault Found:

01314 - Engine Control Module

49-10 - No Communications - Intermittent

I am also looking for a firm answer on if I should be able to access the Central Convenience Module or if my Year 2000 1.4 SE Polo even has it or not.

 

[inder]

Quote: posted by Uwe on 02/04/2005 16:49:37

"A Serial Cable" is not a type of interface.

I'm guessing what your response really means is that you bought some third party interface, perhaps off eBay? If so, have you considered asking the vendor or manufacturer of this interface for assistance?

-Uwe-

Hi Uwe, thanks for the reply. I am not looking for cable assitance, I am looking for info about this error code Vag-Com has found for me:

1 Fault Found:

01314 - Engine Control Module

49-10 - No Communications - Intermittent

I am also looking for a firm answer on if I should be able to access the Central Convenience Module or if my Year 2000 1.4 SE Polo even has it or not.

 

[Uwe]

That fault code means at some point, your instrument cluster wasn't able to talk to your ECU. Perhaps you had the ECU out of the car and turned the ignition on? If not, then you ECU may be dodgy, or the connection(s) between the cluster and the ECU.

I don't know whether your Polo has a Central Convenience module or not. Does it have electric power windows?

-Uwe-

 

[inder]

Thanks for the reply Uwe. I have never touched the ECU myself, so your suggestion of poor connections could be something for me to look at, I will see if any connectors are loose etc.. I have not scanned since, so it the error may have gone, might clear it, drive around and check again

Yes, my polo has electric power windows and sunroof with total closure

Once again, thanks for the advice and suggestions[^]